Part of POCO guides, HyperOS guides, 2025 guides.

You saw the Realme UI port running on a POCO X7 Pro and it looks nothing like HyperOS. Different launcher, different animations, different feel. Now you want it on your phone and you are wondering how much of a job that is.

It is a short job if you do not improvise. It is a long, painful evening if you do, because a port is not a ROM built for your device. Someone took Realme firmware and made it boot on the POCO X7 Pro. That changes the rules.

What you actually need

• A POCO X7 Pro with an unlocked bootloader. There is no way around that.
• The Realme UI port package from the link on this page. The exact one, not a similar one from another device.
• ADB and Fastboot on your PC, plus the USB driver installed so Windows sees the phone in fastboot mode.
• A full backup, because this wipes everything on internal storage.
• Patience for a slow first boot. A port always takes longer to come up than a normal ROM.

Step 1 — back up everything off the phone

Not to the internal storage. Off it, somewhere else. A port flash formats data, so anything still on the phone is gone. Photos, downloads, chat backups, all of it needs to move to a PC or the cloud first.

Step 2 — get your PC talking to the phone

Install the ADB and Fastboot tool, then the driver. Boot the phone into fastboot mode and confirm the PC sees it before you go any further. If the phone shows as an unknown device in Device Manager, stop and fix that now. Nothing later in this guide works if the PC cannot see the phone.

Step 3 — boot the POCO X7 Pro into fastboot mode

Power off, then hold the correct key combination until the fastboot screen appears. Confirm again with your PC that the device is detected. This check takes five seconds and saves an hour.

Step 4 — follow the flashing order

The vendor side goes first, then the ROM. Do not mix the order up and do not skip a step because it looked unimportant. If your port package includes a vbmeta file, it is there for a reason — an AOSP-based package needs it handled at the right point.

Let each fastboot command finish. The terminal prints, waits, and then moves on. Do not pull the cable because a line took thirty seconds.

Step 5 — move into recovery and format data

Recovery is where you format data before the first boot. This is not optional on a port. Flashing a port over old data is how you get a bootloop and then spend two hours convinced the package is broken.

Step 6 — first boot, and then wait

Boot to system and let it settle. The first start on a port is slow. Give it several minutes on the logo before you start worrying. When it comes up, keep the phone idle for a bit and let things finish initialising before you start installing apps.

Where people get stuck

• Mixing files. Use the exact port package from this page. A package pulled from another device, or a mix of two downloads, is the fastest route to an unbootable phone.
• Skipping format data. A port flashed over old data bootloops almost every time. Do the format in recovery, every time, no exceptions.
• Pulling the cable early. Fastboot steps take time. Let every one finish before you touch anything, and never unplug mid-flash.

An honest note

A port is an experiment, not a guaranteed daily driver. It might come with a camera quirk, a sensor behaving oddly, or a calling issue. That is the nature of running firmware adapted from a different phone, and no guide can promise otherwise.

So treat it that way. Keep a backup, keep the official HyperOS package handy so you can go back, and do not put it on a phone you depend on for work the same day.

Going back to HyperOS is possible with a fastboot flash of the official ROM. That is your escape hatch, and knowing it exists is what makes trying a port reasonable in the first place.

If the driver and fastboot setup is the part that always slows you down, the free Rom Flasher tool on GitHub bundles the ADB and fastboot driver install into a couple of clicks. It is free, and the link is on this page.

Full description from the video

Realme UI ported onto the POCO X7 Pro — the whole flash, start to finish, in one quick guide. Fastboot, recovery, and what to check before you commit.

Port ROMs are a different kind of job. You're not flashing something the maintainer built for this exact phone; someone adapted a firmware from another device to run on the POCO X7 Pro. That's why this one stays short and careful: get the files right, follow the order, and don't improvise halfway through fastboot. The payoff is a UI that looks and behaves nothing like HyperOS, so it's worth the extra attention.

📱 Device : POCO X7 Pro

🧩 ROM : Realme UI (port, unofficial)

🛠️ What You Need

• POCO X7 Pro with an unlocked bootloader
• The Realme UI port package from the link below
• ADB and Fastboot tool plus the USB drivers on your PC
• A full backup, because this wipes everything
• Patience for a slow first boot

📝 Steps

1. Back your data up off the phone first.
2. Install the ADB and Fastboot tool on your PC and get the drivers talking to the device.
3. Boot the POCO X7 Pro into fastboot mode.
4. Follow the flashing order shown in the video — vendor side first, then the ROM.
5. Move into recovery and format data before the first boot.
6. Boot to system and let it settle. A port always takes longer on the first start than a normal ROM.

⚠️ Where People Get Stuck

• Mixing files. Use the exact port package from this video, not one pulled from another device.
• Skipping format data. A port flashed over old data is a bootloop.
• Pulling the cable early. Let fastboot finish every step before you touch anything.

❓ Common Questions

Does this need an unlocked bootloader? Yes, there's no way around that on the X7 Pro.

Will Google apps work? That depends on what the port ships with. The video shows what's on screen after the first boot.

Is it stable on the POCO X7 Pro? It's a port, so treat it as an experiment and keep a backup.

Can I go back to HyperOS? Yes, with a fastboot flash of the official ROM.

Common questions

More for POCO X7 Pro